2 3/4" Discoidal Made of Oolitic Material

2 3/4" Discoidal Made of Oolitic Material. This piece is nicely polished on both faces. Both sides are dished out in the center for use as a nutting stone or perhaps as a friction fire starter. Under

2 3/4" Cupped Discoidal. Van Buren Co, IA. Very well made, fine symmetry. Nicely polished, speckled Granite. Ex-Chris Oswald. Davis G9 COA

2 3/4" Jersey Bluff Discoidal. Jersey Co, IL. Granite. Well made, fine condition. Good symmetry

4x 2 5/8" Well made wire material, 3/4" grooved axe, damage to butt end

2 3/4" Modern Hardstone Discoidal. Nicely made discoidal out of a very pretty rock. Likely made by the late Donnie Johns or one of the other hard stone makers in east central Illinois.

An Alef Judaica Rosh Hashana Shofar, a traditional curved musical horn made from natural materials. It is used on the High Holidays. Dimensions: Length 34 1/2" in All measurements are approximate

2 3/4" Panel type Bannerstone. Madison Co, KY. Made of Coquina Fossilized Limestone. Rare material type. Excellent condition. Ex-Joey Ellis. Caddo Trading Company G9 COA

Four Kentucky Adena Points made of contrasting materials. 2 7/8" to 3 3/4". Ex-Glenn McQuaide

Nice example found in Oklahoma made from a gray swirled with black speckled material Stermer identifies as Boone Chert. Excellent form. Stermer COA.

Aluminum hilt marked “F / MADE IN HUNGARY”, sharp double edged blade with saw, scabbard is of a resin water resistant material with two buckled straps. Dimensions: L: 13 1/2 in., (34.5 cm.

10 1/2" 3/4 Groove Axe. Pike Co, IL. A large and very well made Axe. A material seam runs across the bottom, otherwise flawless. We've had mixed reviews on this Axe and are selling it "as-is". Ex-Hube

Lovely Mixed Material Pendant and Brooch in One. Enamel And gold tone mesh Asian bird. Signed Sterling. Measures 2.5 x 1.5 in. Vermeil over sterling and multi colored enamel. Made in China. .34 ozt to

Blade Length: 3 inches Frame Length: 4 1/2 inches Blade Steel: ATS-34

Blade Length: 3 3/4 inches Handle Length: 4 1/2 inches<

Blade Length: 3 3/4 inches Handle Length: 4 1/2 inches<

Blade Length: 3 1/2 inches Frame Length: 4 1/2 inches Blade Steel: ATS-34

Blade Length: 2 3/4 inches Frame Length: 3 1/2 inches Blade Steel: ATS-34

Blade Length: 2 7/8 inches Frame Length: 3 1/2 inches Blade Steel: ATS-34

Blade Length: 2 3/8 inches Frame Length: 3 1/2 inches Blade Steel: ATS-34

Blade Length: 3 3/8 inches Frame Length: 4 1/2 inches Blade Steel: ATS-34

Blade Length: 2 5/8 inches Frame Length: 3 1/2 inches Blade Steel: ATS-34

2 7/8" Wide and made from a very desirable material. Found in Fulton Co. IL.

Blade Length: 2 1/4 inches Frame Length: 2 3/4 inches Blade Steel: ATS-34

Blade Length: 1 1/2 inches Frame Length: 2 1/16 inches Blade Steel: ATS-34 Frame Steel: 416 Stainless Steel Handle Material: Fossil Mammoth Engraver: Ron Scaggs, Relieved Scroll About the Knife Maker: